| Product name | Total organic carbon analyzer (TOC analyzer) | |
|---|---|---|
| Model | HT-110 | |
| Measurement method | Continuous UV oxidation conductivity method | |
| Measurement limit | 0 ppb to 1000 ppb | |
| Measurement range | 0 ppb to 100/500/1000 ppb | |
| Repeatability | Within ±2% of full scale | |
| Display resolution | 0.1 ppb (0 ppb to 100 ppb/0 ppb to 500 ppb range) 1 ppb (0 ppb to 1000 ppb range) | |
| Transmission output | Number of output point: one 4 mA to 20 mA DC/0 V to 1 V DC (optional) insulated input/output Maximum load resistance: 600 Ω (minimum load resistance 100 kΩ (when optionally selected)) Transmission output range: optional setting possible within measurement range Output target: TOC concentration | |
| Contact output | Number of outputs: 2 Alarm contact output (RLY1) Contact method: relay contact, SPDT (1c) Contact capacity: 125 V 3 A AC/24 V 3 A DC (load resistance) Contact function: upper/lower limit function (ON/OFF control) Output target: at TOC, temperature, conductivity: C-NO contact is “closed” during operation, “open” during normal conditions (including a POWER OFF state) *C-NO contact is reversed at hold, or error: C-NO contact is “open” during operation (including a POWER OFF state), “closed” during normal conditions *C-NO contact is reversed | |
| Alarm contact output (RLY2) Contact method: relay contact, SPST (1a) Contact capacity: 125 V 3 A AC/24 V 3 A DC (load resistance) Contact function: upper/lower limit function (ON/OFF control) Output target: TOC concentration | ||
| Contact input | Number of input point: 1 Non-voltage normal open (1a) signal input (open collector input possible) Insulation-type input Max. ON resistance: 50 Ω Open-circuit voltage: 5 V DC Max. short circuit current: 10 mA An error will not be generated even if there is notification of no sample detection immediately after receipt of the pure water device stop signal receiving The hold operation during the contact input receiving. | |
| Sample water condition | Conductivity: less than 10 μS/cm (less than 2 μS/cm in 0 ppb to 100 ppb range) | |
| Temperature: 5℃ to 99℃ | ||
| Pressure: 0.03 MPa to 0.50 MPa, Pressure fluctuation: within ±0.05 MPa (within the specified pressure range) | ||
| Flow rate: 20 mL/min to 200 mL/min | ||
| Environmental conditions | Temperature: 5℃ to 40℃ | |
| Relative humidity: less than 85% | ||
| Installation | Install place: indoor | |
| Display function | LCD (with a back light) TOC, conductivity, water temperature, alarm | |
| Power | 100 V to 240 V AC ±10%, 50 Hz/60 Hz built-in fuse 250 V AC 3.15 A (T) | |
| Power consumption | 80 VA (max.) | |
| Outside dimension | 300 (W) × 400 (H) × 165 (D) mm | |
| Mass | 13 kg | |
| Concerned directives | CE marking | EMC Directive: EN61326-2-3 Low Voltage Directive: EN61010-1 RoHS Directive: EN50581 |
| FCC Rule | FCC parts 15 | |
| Protection structure | IP 43 (IEC60529, JIS C0920) Pollution level 2 (IEC61010-1) | |
HT-110
On-line TOC analyzer
High-precision continuous measurement of TOC in water used for pharmaceutical manufacturing and similar applications.
HT-110 is a TOC analyzer designed for water used in pharmaceutical manufacturing, which adopts the continuous UV oxidation and conductivity method as the measurement principle. In compliance with the USP (U.S. Pharmacopeia) reference standard, it is characterized by its ability to continuously measure low-concentration ranges, such as water for injection, with high accuracy.
Segment: Process And Environmental
Division: Process Water
Manufacturing Company: HORIBA Advanced Techno Co., Ltd.
Adoption of UV Oxidation Conductivity Method
The UV oxidation conductivity method, which eliminates the need for reagents and carrier gasses (purge gas) has been adopted. This method allows for high repeatability of ±2％ F.S. for low-concentration ranges such as water for injection (WFI) at full scale while simultaneously providing a potential reduction in operating expenses.
Suppression of Erroneous Indications Caused by Air Bubble Inclusion
The equipment has a deaeration mechanism, which suppresses erroneous indications caused by the inclusion of air bubbles.
External control functions
By equipping contact input terminals, it is now possible to perform ON/OFF controls externally. Useful for situations such as false alarms during SIP cleaning or nighttime shutdown of purified water equipment.
Maintenance cycle of one year
By significantly extending the lifespan of the UV lamp, maintenance is now reduced to a single annual calibration, allowing a maintenance-free period of one year.
Compatible with USP<643>, EP<2.2.44>, JP<G8.4.5.2>
Suitable for TOTAL ORGANIC CARBON measurement according to USP <643>, EP <2.2.44>, and for the suitability testing of "HIGHLY PURIFIED WATER", "WATER FOR INJECTION", and "WATER, PURIFIED" as per EP requirements. It is also ideal for the physicochemical monitoring specified in JP <G8.4.5.2> for PW (Purified Water) and WFI (Water for Injection).
Versatile installation options
The installation methods include pole-mounts, wall-mounts, and tabletops, allowing for flexible installation options tailored to the specific site requirements for versatile installations without limitations.
